Author Topic: Tips for installing shoot-thru-the-hull puck transducer  (Read 2533 times)

0 Members and 1 Guest are viewing this topic.

Offline grey2112

  • Newbie
  • *
  • Joined: Feb 2012
  • Location: New Port Richey, FL USA
  • Posts: 13
Tips for installing shoot-thru-the-hull puck transducer
« on: October 30, 2012, 08:11:05 AM »
Decided to add a shoot-thru-the-hull puck transducer to my setup - currently have an 1198cSI/DI with the transducer on the transom, but at speed and in rough conditions it is less than ideal for picking up depth and bottom soundings.  Going to try the shoot-thru for that after using the Y cable so that I still retain SI/DI using the external transducer.

The guys at Key West told me that the only "cored" part of my hull that I could not mount the puck was in an 8" square around the bilge pump/float switch in the bilge. 

So, is there a trick to allow for me to try out various places in the bilge without permanently attaching it until I find the right place?  I was almost thinking of creating a tube, say out of PVC, with plumbers putty on the bottom edges to help stick and conform to the slightly angled bilge, and then putting mineral oil in it and then place the puck in it - I could then move it around while testing it in the water to see how well it worked before permanently mounting it.


Offline Humminbird_Greg

  • Humminbird Helper
  • Humminbird Staff
  • *
  • Joined: Mar 2009
  • Location: Eufaula, AL.
  • Posts: 6546
  • I help because I can
    • Humminbird Web Site
Re: Tips for installing shoot-thru-the-hull puck transducer
« Reply #1 on: October 30, 2012, 01:51:28 PM »
Look for the Inside the Hull Installation instructions here:
http://forums.sideimagingsoft.com/index.php?topic=2984.0

I would add that you should use something to remove any paint or other coatings from the inside of the fiberglass hull before testing or installing.  Some have used an appropriately sized Fortner bit for this.  The idea is to get down to the raw fiberglass so that there is nothing else there to block the sonar.  It also will make a good surface for the epoxy to bond to.

I posted images about the PVC pipe on one of the posts you made on another web site.

Greg Walters at Humminbird
gwalters@johnsonoutdoors.com


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
6 Replies
6647 Views
Last post April 14, 2010, 02:45:32 PM
by Humminbird_Greg
1 Replies
4180 Views
Last post June 27, 2010, 12:04:16 AM
by RGecy
8 Replies
9662 Views
Last post March 13, 2011, 05:47:57 PM
by lolar3288
3 Replies
2422 Views
Last post February 18, 2012, 10:49:25 PM
by choc_e
18 Replies
8170 Views
Last post March 29, 2012, 10:08:32 AM
by sonar2000
4 Replies
3523 Views
Last post July 21, 2014, 04:13:30 PM
by TXAG DAC
3 Replies
4266 Views
Last post February 20, 2015, 04:04:47 PM
by Humminbird_Greg
2 Replies
1604 Views
Last post March 09, 2015, 04:10:44 PM
by TheSavant


SimplePortal 2.3.3 © 2008-2010, SimplePortal