Author Topic: Helix 9 SI and two plus transducers  (Read 4194 times)

0 Members and 1 Guest are viewing this topic.

Offline HONDO

  • Newbie
  • *
  • Joined: Mar 2016
  • Location: Virginia
  • Posts: 2
  • Unit(s): Helix 9 SI GPS
  • Accessories: HDSI transducer, SI transducer
Helix 9 SI and two plus transducers
« on: March 14, 2016, 07:03:51 PM »
I just bought a Helix 9 SI.  I also purchased a XTM 9 HDSI 180 T for the trolling motor.  The transducer that came with the unit will go on the transom AND I have another high speed transducer that is / was for another unit but it is compatible with the helix 9 as well.

I haven't unpacked the Helix yet but I have mounted the HD transducer I on the trolling motor.

Before I spend the time mounting the regular SI transducer, will I need a switch to use both of these transducers?  I've read about a SILR Y cable...  is that all is takes?  If so, would it then be possible to daisy chain a couple of those y cables and add a third high speed transducer?

any thoughts or recommendation are appreciated!

Thanks! Rich



Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Helix 9 SI and two plus transducers
« Reply #1 on: March 15, 2016, 12:17:10 AM »
The HB TS3 switch is needed to connect 2 SI xducers to 1 head unit ... It allows use of only 1 of the SI xducers at a time ...
http://www.humminbird.com/Products/TS3/
-----

The AS SIDB Y cable is needed to connect a Dual Beam (2d) xducer to one of the SI units ... The AS SIDB Y cable is a cable splitter that disconnects the 2d piezo in the SI xducer and wires in the Dual Beam xducer in its place ... The head unit that uses the AS SIDB Y cable connection "sees" this setup as 1 xducer... because it's merely rerouting wire channels in the cables ...
http://www.humminbird.com/Products/AS-SIDB-Y/

Rickie
« Last Edit: March 15, 2016, 12:18:39 AM by rnvinc »

Offline HONDO

  • Newbie
  • *
  • Joined: Mar 2016
  • Location: Virginia
  • Posts: 2
  • Unit(s): Helix 9 SI GPS
  • Accessories: HDSI transducer, SI transducer
Re: Helix 9 SI and two plus transducers
« Reply #2 on: March 15, 2016, 10:13:00 PM »
Rickie,

If I understand you correctly, the diagram I just made should work.  The HDSI is on the trolling motor, the regular SI under the step on the transom and the dual beam on the outside drivers side of the transom.

so when the trolling motor is UP and the HDSI is out of the water, the dual beam will still read at high speed, correct?   and then if I want to run slow and si image with the engine, the regular SI will handle that with a flip of the switch.

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Helix 9 SI and two plus transducers
« Reply #3 on: March 15, 2016, 11:39:33 PM »
Almost ...

Your diagram shows the AS SILR Y cable  ... ("LR" indicates left/right) ...used with 2 separate HDSI xducers in a Setup where left SI comes from the port HDSI xducer and right SI/2d/temp comes from the starboard HDSI xducer (sometimes beneficial when blockage on one side is imminent with 1 HDSI xducer alone) ...

Your setup should use the AS SIDB Y cable ... ("DB" indicates Dual Beam) ...used with 1 HDSI xducer and 1 Dual Beam xducer ...
http://www.humminbird.com/Products/AS-SIDB-Y/

The rest of your diagram is correct ...
« Last Edit: March 15, 2016, 11:45:07 PM by rnvinc »

Offline fishreed

  • Full Member
  • ***
  • Joined: Mar 2015
  • Location: Byron, Michigan
  • Posts: 153
  • fishreed
  • Unit(s): 899CI SI HD,1199SI HD, Helix 12 SI GEN3
  • Software: current
  • Accessories: ALL, and a HW ducer for the Helix 12 2D
Re: Helix 9 SI and two plus transducers
« Reply #4 on: March 20, 2016, 02:03:33 PM »
Almost ...

Your diagram shows the AS SILR Y cable  ... ("LR" indicates left/right) ...used with 2 separate HDSI xducers in a Setup where left SI comes from the port HDSI xducer and right SI/2d/temp comes from the starboard HDSI xducer (sometimes beneficial when blockage on one side is imminent with 1 HDSI xducer alone) ...

Your setup should use the AS SIDB Y cable ... ("DB" indicates Dual Beam) ...used with 1 HDSI xducer and 1 Dual Beam xducer ...
http://www.humminbird.com/Products/AS-SIDB-Y/

The rest of your diagram is correct ...


I agree too....you need to use the SIDB Y cable!


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
0 Replies
3479 Views
Last post July 18, 2015, 09:21:43 PM
by shanemcg83
5 Replies
6127 Views
Last post January 11, 2016, 09:02:24 AM
by rnvinc
3 Replies
4921 Views
Last post October 08, 2016, 10:09:16 PM
by Rpadar
15 Replies
10548 Views
Last post September 03, 2016, 09:35:03 PM
by Sewerdude
1 Replies
4503 Views
Last post June 07, 2017, 11:25:19 PM
by rnvinc
1 Replies
2929 Views
Last post August 05, 2017, 02:00:20 AM
by rnvinc
4 Replies
4029 Views
Last post January 16, 2022, 12:38:53 PM
by fishingottawa
8 Replies
1138 Views
Last post November 27, 2023, 04:20:42 AM
by John Coward


SimplePortal 2.3.3 © 2008-2010, SimplePortal