| Name |
Posted |
Views |
Comments |
Rating |
|
ProCraft 205 SI Transducer Install
posted by mperdue
|
March 03, 2015, 04:45:14 PM |
1486 |
|
|
|
ProCraft 205 999ci HD Back View
posted by mperdue
|
March 03, 2015, 04:43:25 PM |
1176 |
|
|
|
ProCraft 205 999ci HD
posted by mperdue
|
March 03, 2015, 04:40:53 PM |
1064 |
|
|
|
Helix 5 SI on Dash and Helix 5 DI up front
posted by PAPA BEAR
|
February 13, 2015, 02:28:56 PM |
1106 |
|
|
|
Here is where I installed my Helix 5 units. 2002 Ranger 175vs.
|
|
DSC03739
posted by Beaulieu80
|
August 22, 2014, 08:38:13 AM |
1410 |
|
|
|
DSC03742
posted by Beaulieu80
|
August 22, 2014, 08:37:27 AM |
1546 |
|
0.13 (1 vote) |
|
DSC03740
posted by Beaulieu80
|
August 22, 2014, 08:36:37 AM |
1459 |
|
|
|
Ranger boat si transducer with shield and saver
posted by viers583
|
January 19, 2014, 08:35:42 PM |
1802 |
|
|
|
Drilled 2 holes through step.
|
|
Ram 111 D mount with HB 898
posted by JDX
|
October 19, 2013, 11:56:33 AM |
1427 |
|
|
|
$75.00 shipped Amazon The best way I found to mount the 898
|
|
XNT type Transducer Roostertail Plug
posted by Humminbird_Greg
|
April 03, 2013, 01:18:13 PM |
2088 |
|
|
|
This is the rubber plug that was developed to help stop the water spray from an XNT type transducer when it is mounted low on the transom.
[540188-1 XNT Plug Bagged Hardware]
|
|
HPIM1052
posted by Roddy
|
September 13, 2012, 09:28:38 PM |
3168 |
|
|
|
THE EQUIPPED FLATS/SAR BOAT 947c, 1158c, 1198c
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:44:35 PM |
2800 |
|
|
|
2011 nitro z-6
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:44:01 PM |
2033 |
|
|
|
2011 nitro z-6
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:43:31 PM |
1910 |
|
|
|
2011 nitro z-6
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:43:01 PM |
1748 |
|
|
|
2011 nitro z-6
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:42:31 PM |
1720 |
|
|
|
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:41:55 PM |
1612 |
|
|
|
2011 Z-6 Nitro, the ram mount base wouldnt mount up very well due to the difference in height between the console and the actual side of the boat. I ended up taking the arm off the base, drilling one hole and installing a large washer . I used the bolt that came in the arm and put it up through the whole I drilled from the bottom. I installed the rubber next , then the arm finishing off the with the quick connect threaded top that came on the arm. It all worked nicely, it also retained its swivel motion.
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:41:05 PM |
2167 |
|
|
|
2011 Z-6 Transducer 997c si. This was the only place I could see working. If the strap wasnt there I could have moved further over. These z-6 dont have a real good spot for the transducer, I almost canceled the install because of it. I wasnt sure how it would end up working but Im happy to say I took the boat out this morning and it actually worked great.
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:40:34 PM |
1461 |
|
|
|
Heres my 2011 Nitro z-6 install. Not alot of room, took a few inovative ideas.
|
|
Packed console!!
posted by edwardpic
|
August 16, 2011, 10:43:11 AM |
1447 |
|
|
|
898c SI Speed boat installation pic #5
posted by Erik Concha
|
May 13, 2011, 03:31:41 PM |
2019 |
|
|
|
898c SI Speed boat installation pic #4
posted by Erik Concha
|
May 13, 2011, 03:29:46 PM |
1616 |
|
|
|
898c SI Speed boat installation pic #3
posted by Erik Concha
|
May 13, 2011, 03:28:16 PM |
1426 |
|
|
|
898c SI Speed boat installation pic #2
posted by Erik Concha
|
May 13, 2011, 03:24:48 PM |
1348 |
|
|
|
898c SI Speed boat installation pic #1
posted by Erik Concha
|
May 13, 2011, 03:19:45 PM |
1514 |
|
|
