Author Topic: Problems with Onix 10, Onix 8, 1198  (Read 14765 times)

0 Members and 1 Guest are viewing this topic.

Offline bassleo

  • Newbie
  • *
  • Joined: Nov 2016
  • Location: GONZAGA (MN) ,ITALY
  • Posts: 6
  • Unit(s): ONIX10-ONIX8_1198CHOsi
  • Software: Onix(2,7)1198(6,67)
  • Accessories: watersense,switch AS ETH 5PXG
Problems with Onix 10, Onix 8, 1198
« on: November 17, 2016, 04:12:50 PM »
Hello, I’m Leonardo from Italy and I’m writing to you for the problems I’ve encountered with my bass boat 2012 Nitro Z8.

After updating all the tools, resetting the ethernet network and checking the tools one by one, I’ve found the following problems:

- Onix 10 bow: the transducer was mounted on a Motorguide IX5. Every time I push the button to start the electric engine the monitors shows vertical lines, thus this is a clear problem of noise created by the engine.

- Onix 8 side console: it presents the Onix 10’s problem if it is connected to the ethernet network.
Another problem rises with the stern transducer directly connected to Onix8, both with and without ethernet connection. After the first test without ethernet connection, after moving with the engine the transducer shows a depth of 1900 meters, then 3590 meters, then 9540 meters and so on. The only way to make it work properly is to reset the transducer setup; however it works until the next navigation. 
I have the same problems also with the latest Onix software update (Version 2.700) and 1198 (Version 7.670).


The ethernet connection was tested both with switch AS ETH 5PXG and directly between the tools.


You can find attached the pictures of the stern transducer


Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Problems with Onix 10, Onix 8, 1198
« Reply #1 on: November 18, 2016, 12:38:42 PM »
1. Trolling motor interference is a common discussion on the forums ...

Read this and follow the steps mentioned ...and then post back if there are still RFI issues ...
http://www.humminbird.com/Category/Support/FAQ/Trolling-Motor-Interference/
-----

2. Ethernet connected units can experience RFI thru the Ethernet cable from another affected unit ... hopefully this issue will go away when the RFI issue in point 1 above is remedied ...
-----

3. The erratic depth readings when the engine is engaged is most likely turbulence created by your prop ... Sonar cant read Thru bubbles ...

This sometimes can be remedied by moving the xducer away from the turbulent water ... (your pic of the transom mounted xducer did not post where we can offer advice on placement ... or did you post the pics in a different sub-forum? ...) ...

Rickie
« Last Edit: November 18, 2016, 12:41:06 PM by rnvinc »

Offline bassleo

  • Newbie
  • *
  • Joined: Nov 2016
  • Location: GONZAGA (MN) ,ITALY
  • Posts: 6
  • Unit(s): ONIX10-ONIX8_1198CHOsi
  • Software: Onix(2,7)1198(6,67)
  • Accessories: watersense,switch AS ETH 5PXG
Re: Problems with Onix 10, Onix 8, 1198
« Reply #2 on: November 22, 2016, 01:55:23 PM »
Hello
here are the pictures of the transducers on my boat Nitro Z8

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Problems with Onix 10, Onix 8, 1198
« Reply #3 on: November 22, 2016, 08:25:10 PM »
My guess is still turbulence created by the prop ...

Are the depth readings correct up until a certain speed is reached ... or do depth readings become erratic as soon as the prop is engaged ...??
----

Another observation with the ONIX SI xducer and 1198 SI xducer side by side ... :

Are you getting right SI blockage in the ONIX SI image ...and left SI blockage in the 1198 SI image ... ??

Rickie
« Last Edit: November 22, 2016, 08:26:13 PM by rnvinc »

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Problems with Onix 10, Onix 8, 1198
« Reply #4 on: November 22, 2016, 08:28:07 PM »
Also ... are any of the remedies for trolling motor RFI in the link I provided working for your interference issues ... ??

Rickie

Offline bassleo

  • Newbie
  • *
  • Joined: Nov 2016
  • Location: GONZAGA (MN) ,ITALY
  • Posts: 6
  • Unit(s): ONIX10-ONIX8_1198CHOsi
  • Software: Onix(2,7)1198(6,67)
  • Accessories: watersense,switch AS ETH 5PXG
Re: Problems with Onix 10, Onix 8, 1198
« Reply #5 on: November 23, 2016, 01:35:24 AM »
hello, I unplugged transducer from 1198 (off) but ONIX reading continues to give me different depths 780 ... 860 ... 910 ... 1050 .... etc but when I turn off the prop and get ready to fish the transducer seems crazy and to make it work again I have to reset it.
« Last Edit: November 23, 2016, 01:11:51 PM by bassleo »

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Problems with Onix 10, Onix 8, 1198
« Reply #6 on: November 23, 2016, 08:06:54 PM »
To get the troubleshooting down to its basic Setup ... you can try disconnecting the networking completely and test the ONIX by itself with nothing else powered on ...

Also try resetting defaults - 1st try resetting Sonar defaults ... if that doesn't help try complete Restore
defaults ...

Rickie

Offline bassleo

  • Newbie
  • *
  • Joined: Nov 2016
  • Location: GONZAGA (MN) ,ITALY
  • Posts: 6
  • Unit(s): ONIX10-ONIX8_1198CHOsi
  • Software: Onix(2,7)1198(6,67)
  • Accessories: watersense,switch AS ETH 5PXG
Re: Problems with Onix 10, Onix 8, 1198
« Reply #7 on: November 24, 2016, 02:01:47 AM »
the test of ONIX alone was made ....... but the result was the same  ??? ???
LEO

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Problems with Onix 10, Onix 8, 1198
« Reply #8 on: November 24, 2016, 07:58:40 PM »
Is the ONIX depth stable if the big motor is not running and the boat adrift ...??

Rickie

Offline bassleo

  • Newbie
  • *
  • Joined: Nov 2016
  • Location: GONZAGA (MN) ,ITALY
  • Posts: 6
  • Unit(s): ONIX10-ONIX8_1198CHOsi
  • Software: Onix(2,7)1198(6,67)
  • Accessories: watersense,switch AS ETH 5PXG
Re: Problems with Onix 10, Onix 8, 1198
« Reply #9 on: November 25, 2016, 02:00:54 PM »
no, it is not stable..........

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Problems with Onix 10, Onix 8, 1198
« Reply #10 on: November 25, 2016, 09:49:15 PM »
no, it is not stable..........


Here are some possibles steps ...:

*Restore Defaults ...
*Turn off SI and DI transmitters and test with only 2d transmitting ...
*Confirm xducer face is level with water's surface ...
*Confirm xducer and xducer cabling are not damaged ...
*Test with replacement ONIX xducer ...(if your ONIX is under warranty HB may send you one) ...
*Test your ONIX head unit on someone else's boat ...
*Test with 1198 xducer connected to ONIX (would need the AD 1429 adapter cable http://www.humminbird.com/Products/AD-1429/ ) ...
*Test with ONIX xducer and 1198 xducer using AS SIDB Y cable http://www.humminbird.com/Products/AS-14-SI-DB-Y/ (would also need AD 1429 listed above) ...

It sounds like the 2d piezo in the ONIX xducer is not functioning correctly ...

Rickie
« Last Edit: November 25, 2016, 09:52:33 PM by rnvinc »

Offline bassleo

  • Newbie
  • *
  • Joined: Nov 2016
  • Location: GONZAGA (MN) ,ITALY
  • Posts: 6
  • Unit(s): ONIX10-ONIX8_1198CHOsi
  • Software: Onix(2,7)1198(6,67)
  • Accessories: watersense,switch AS ETH 5PXG
Re: Problems with Onix 10, Onix 8, 1198
« Reply #11 on: December 03, 2016, 04:36:20 AM »
I've have done all the steps listed above. The only thing that is left to do is to completely reset the ONIX, I have been told that the only way to do it is by connecting the onix to a computer. Is it right? if yes, which cable should I use?

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: Problems with Onix 10, Onix 8, 1198
« Reply #12 on: December 03, 2016, 08:13:28 AM »
This is the procedure for ONIX hard reset ... (this will put the unit back to its original software version and erase any personal data) ...

In quick succession ...:

*Press and hold check -
*Press and hold x -
*Press Power -
*Release all 3 ...


Have you talked to anyone at HB about your issues ...??

Rickie

« Last Edit: December 03, 2016, 08:15:31 AM by rnvinc »


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
3 Replies
13377 Views
Last post May 07, 2014, 04:27:24 AM
by Nitro78
9 Replies
21879 Views
Last post July 01, 2014, 02:12:18 AM
by Nitro78
10 Replies
7949 Views
Last post July 14, 2014, 09:38:42 PM
by CarolC
2 Replies
2985 Views
Last post November 13, 2014, 08:16:31 AM
by lcookie
3 Replies
2681 Views
Last post March 23, 2015, 11:28:33 AM
by metalworx
7 Replies
5204 Views
Last post May 30, 2015, 09:51:41 PM
by RonnieB
5 Replies
4803 Views
Last post May 19, 2015, 07:05:18 AM
by Vinniez520
1 Replies
2620 Views
Last post February 29, 2016, 09:54:06 PM
by rnvinc


anything
SimplePortal 2.3.3 © 2008-2010, SimplePortal