Author Topic: Transducer location  (Read 4864 times)

0 Members and 1 Guest are viewing this topic.

Offline bakerdave

  • Newbie
  • *
  • Joined: Mar 2010
  • Location: ohio
  • Posts: 17
  • Unit(s): 898c si
Transducer location
« on: April 29, 2010, 05:18:10 PM »
I will try to post a pic of my transom when my boat is out of the shop. Impellar went and enginge overheaeted, what a mess. The hull is a deep v
i have tried the transducer on both port and starboard side of transom. It is mounted right now 15 inches fro prop. at low speeds (less than 7mph) i am unable to get a reading on side imaging on the side towards the prop. The transducer is just barely below the lowest point on the lower unit. I am unable to mount any lower without getting closer to the prop. when is am running at about 10mph it works fine. am i getting cavitation from prop causing me to loose signal on the one side. I should say that on the side towards the prop i do get a small amount of imaging on screen and then the rest is unreadable. (if that make sense).. I saw that humminbird has a splitter for the transducer cable, can i run 2 transducers with one on either side.


Offline Humminbird_Greg

  • Humminbird Helper
  • Humminbird Staff
  • *
  • Joined: Mar 2009
  • Location: Eufaula, AL.
  • Posts: 6546
  • I help because I can
    • Humminbird Web Site
Re: Transducer location
« Reply #1 on: April 30, 2010, 11:42:07 AM »
Not sure I am understanding what you are saying about the signal loss, prop and all so will wait to comment when I see pictures of your boat.

Yes you can run two Si transducers one on each side of the motor and connect them together with the AS-Si-LR-Y transducer splitter cable.

Greg Walters at Humminbird
gwalters@johnsonoutdoors.com

Offline bakerdave

  • Newbie
  • *
  • Joined: Mar 2010
  • Location: ohio
  • Posts: 17
  • Unit(s): 898c si
Re: Transducer location
« Reply #2 on: April 30, 2010, 03:15:20 PM »
may try the 2 transducers. I will post a pic when i get the boat on the water. on side imaging were you see water depth down the center dividing the 2 sides, you get about an inch bottom view below water level and then the rest of the screen just looks like white noise. The other side shows a good bottom view accross screen


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
14 Replies
19789 Views
Last post February 19, 2010, 03:51:33 PM
by sonar2000
7 Replies
7605 Views
Last post April 06, 2010, 06:11:22 PM
by jimf
6 Replies
13313 Views
Last post April 15, 2010, 10:41:52 AM
by Howie
8 Replies
5824 Views
Last post May 12, 2010, 08:34:39 PM
by calli1
1 Replies
4010 Views
Last post April 15, 2013, 03:05:31 PM
by Humminbird_Greg
5 Replies
4324 Views
Last post March 25, 2016, 05:56:45 PM
by fishreed
9 Replies
7178 Views
Last post April 06, 2016, 08:43:34 AM
by jabsy
6 Replies
6406 Views
Last post February 04, 2017, 02:34:58 PM
by newkid4si


anything
SimplePortal 2.3.3 © 2008-2010, SimplePortal