Humminbird Side Imaging Forums

Side Imaging Forums => Onix and Ion Series => Topic started by: danlaboucane on December 03, 2017, 08:41:17 AM

Title: to see left side imaging sides on one screen and right on another
Post by: danlaboucane on December 03, 2017, 08:41:17 AM

how to see left side imaging side on one screen and right on another ? do i need two transducers ? each connected to different units or can i share a different side of the SI by ethernet ?

Title: Re: to see left side imaging sides on one screen and right on another
Post by: rnvinc on December 03, 2017, 10:01:24 AM

The only SI/SI Combo view available is the stacked SI view as seen below with version 1.350 in HELIX series  ...(Not sure the version number in ONIX or SOLIX)  ...

(https://lh3.googleusercontent.com/PTZFwhqhi6ciA6GcBFvAf3Z9r2dhkU889879kE5iuDIxI6qpbVA7ZqhJq5ku8EqdRhCbksNPnoF2smbhEr1VM-qFweyBDA0OBBW8UVWnq7fJxQhKiDxtbv15hup-z-iwAe-TwdYNvA)

This view can be created with both left SI data and right SI data coming from the same SI xducer  ...

Or from 2 SI xducers using the AS SILR Y cable for HELIX G1 series  ...
https://www.humminbird.com/productDetail-Accessory.aspx?Pageid=728&id=977 (https://www.humminbird.com/productDetail-Accessory.aspx?Pageid=728&id=977)

Or from 2 SI xducers using the SM SILR Y Cable for HELIX MEGA series  ...
https://www.humminbird.com/Products/SM-SILRY/ (https://www.humminbird.com/Products/SM-SILRY/)

Or from 2 SI xducers using the AS 14 SILR Y Cable for ONIX series  ...
https://www.humminbird.com/productDetail-Accessory.aspx?Pageid=728&id=3321 (https://www.humminbird.com/productDetail-Accessory.aspx?Pageid=728&id=3321)

Or from 2 SI xducers using the SM SILR Y Cable for SOLIX series  ...
https://www.humminbird.com/Products/SM-SILRY/ (https://www.humminbird.com/Products/SM-SILRY/)
-----

Left SI data and right SI data cannot be shared separately thru Ethernet  ...

Rickie

Title: Re: to see left side imaging sides on one screen and right on another
Post by: danlaboucane on December 03, 2017, 10:46:58 AM

but if i use two onix SI units connected to two different transducers can i choose to display right side on right screen and left  side on the left screen ? and still be ethernet connected ? i would use that when trolling and bring a unit on the bow when casting .

Title: Re: to see left side imaging sides on one screen and right on another
Post by: rnvinc on December 03, 2017, 10:53:25 AM

Quote from: danlaboucane on December 03, 2017, 10:46:58 AM

but if i use two onix SI units connected to two different transducers can i choose to display right side on right screen and left  side on the left screen ? and still be ethernet connected ? i would use that when trolling and bring a unit on the bow when casting .

I'm afraid not  ... Sharing SI thru Ethernet specifies SI from "Unit 1" or SI from "Unit 2"  ... which, in effect, requires sharing "left SI data and right SI data"..

There is no selection choice to share "left SI data or right SI data"  ...

Rickie

Title: Re: to see left side imaging sides on one screen and right on another
Post by: danlaboucane on December 03, 2017, 11:44:07 AM

ok thanks rickie, but i would still be able to isolate right and left on the two units at console ?

Title: Re: to see left side imaging sides on one screen and right on another
Post by: rnvinc on December 04, 2017, 09:44:39 PM

Quote from: danlaboucane on December 03, 2017, 11:44:07 AM

ok thanks rickie, but i would still be able to isolate right and left on the two units at console ?

Correct  ... And probably a better option anyway so that left SI can be full screen on the left unit and right SI could be full screen on the right unit  ...

Rickie