Views: 3561
Posted by dybvad417
May 15, 2009
|
HPIM1052
THE EQUIPPED FLATS/SAR BOAT 947c, 1158c, 1198c
Views: 3072
Posted by Roddy
Sep 13, 2012
|
Views: 3007
Posted by xd35
Apr 15, 2010
|
Tranducer Installation on Stepped Deep V Hull
Tranducer Installation on Stepped Deep V Hull
Views: 2801
Apr 03, 2009
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 2716
Posted by Neverenuff
Dec 10, 2011
|
Humminbird 798c SI transducer on a Ranger 175 under a 5 1/2" CMC Power-Lift jackplate.
Humminbird 798c SI transducer on a Ranger 175 under a 5 1/2" CMC Power-Lift jackplate.
Views: 2566
Posted by John175
Jun 30, 2009
|
SI on SternMate™ 2
View from port. Hummingbird SI transducer is mounted on a SternMate™ transducer mounting system. The system is installed using a proprietary high speed adhesive without the necessity of damaging screw holes. The boat is our 16DLX Carolina Skiff. Boaters worldwide are now mounting their transom-moun…
Views: 2158
Posted by Captn_C
Mar 20, 2010
|
Kayak stern mount 798ci - rear view
Fabricated kayak stern mount for my 798ci transducer. Not sure if turbulence from hull will impact the image quality.
Views: 2125
Posted by kayakangler
Jul 14, 2009
|
'11 nitro z-6 997c si install
2011 Z-6 Transducer 997c si. This was the only place I could see working. If the strap wasnt there I could have moved further over. These z-6 dont have a real good spot for the transducer, I almost canceled the install because of it. I wasnt sure how it would end up working but Im happy to say I too…
Views: 2065
Posted by Neverenuff
Dec 10, 2011
|
Views: 2061
Posted by xd35
Apr 15, 2010
|
XNT type Transducer Roostertail Plug
This is the rubber plug that was developed to help stop the water spray from an XNT type transducer when it is mounted low on the transom. [540188-1 XNT Plug Bagged Hardware]
Views: 2002
Posted by Humminbird_Greg
Apr 03, 2013
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 1934
Posted by Neverenuff
Dec 10, 2011
|
898c SI Speed boat installation pic #5
Views: 1924
Posted by Erik Concha
May 13, 2011
|
Transducer Mount on ProCraft Fish and Ski
Views: 1894
Comments: 1
Posted by tenndave
Feb 03, 2011
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 1800
Posted by Neverenuff
Dec 10, 2011
|
HDSI install on V-Hull
pic 6
Views: 1731
Posted by xd35
Mar 15, 2010
|
Ranger boat si transducer with shield and saver
Drilled 2 holes through step.
Views: 1711
Posted by viers583
Jan 19, 2014
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 1649
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
Views: 1625
Posted by Neverenuff
Dec 10, 2011
|
Views: 1561
Posted by J Linville
Jun 10, 2010
|
2010 04 27 1746
898c Install - Lund 17 Ft Explorer
Views: 1550
Posted by Deltaden
May 02, 2010
|
898c SI Speed boat installation pic #4
Views: 1532
Posted by Erik Concha
May 13, 2011
|
'11 nitro z-6 997c si install
2011 Z-6 Nitro, the ram mount base wouldnt mount up very well due to the difference in height between the console and the actual side of the boat. I ended up taking the arm off the base, drilling one hole and installing a large washer . I used the bolt that came in the arm and put it up through the…
Views: 1506
Posted by Neverenuff
Dec 10, 2011
|
Views: 1471
Posted by bigbass
Apr 29, 2011
|
2010 04 27 1740
898c Install - Lund 17 Ft Explorer
Views: 1467
Posted by Deltaden
May 02, 2010
|