Author Topic: Helix 10 mega trolling motor interference.  (Read 153 times)

0 Members and 1 Guest are viewing this topic.

Offline Texasdood57

  • Newbie
  • *
  • Joined: Jun 2017
  • location: Helix 10 mega combo
  • Posts: 1
  • Unit(s): Helix 7 kvd combo
  • Accessories: N/a
Helix 10 mega trolling motor interference.
« on: June 08, 2017, 08:36:46 PM »
Me and my father just recently installed a helix 10 mega on his boat along with a minnkota ulterra. When the motor isnt running or on high speed the SI and DI look great but on any other speed we get terrible interference. If i unplug the i-pilot link the interference goes away. The i-pilot link and trolling motor cables are run on seperate sides of the boat and only meet at the bow of the boat. I havent tried moving the wire away from the trolling motor plug yet. Was just wondering if there was an easier fix then drilling another hole in the boat. Boat is a sea pro 2001


Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • location: Western KY
  • Posts: 2962
  • Unit(s): 1197c SI Combo, Onix 8ci SI Combo
  • Software: Dependent on whim
  • Accessories: AS GRHA, AS GPS HS, LowBird LSS 1 & 2
Re: Helix 10 mega trolling motor interference.
« Reply #1 on: June 09, 2017, 07:52:36 PM »
The 1st step should be to determine if the interference is encroaching into the xducer/cable or encroaching into the HELIX power circuit  ...

This can be identified by separating the xducer and it's cable from the TM and test the xducer hanging in the water completely away from the TM  ...

If the interference goes away - we know the interference is encroaching into the xducer or xducer cable  ...
If the interference is still present - we know the interference is encroaching into the power circuit  ...

Either way lends to a path forward for dealing with interference  ...

Rickie

Offline zip308

  • Newbie
  • *
  • Joined: Jun 2016
  • location: MN
  • Posts: 5
  • Unit(s): Helix 10SI - Helix 9 - Helix 5 - 899SI
  • Software: new
  • Accessories: Networking - GPS w/HS
Re: Helix 10 mega trolling motor interference.
« Reply #2 on: June 12, 2017, 10:44:26 AM »
I had the same problem and just posted what I found:

http://forums.sideimagingsoft.com/index.php?topic=9660.0

If you are connecting the Ulterra directly to your Helix and not using the AS ETH 5PXG network switch try grounding the metal barrel connectors where the Ethernet cables connect together to the negative of your cranking battery (assuming that is where your Helix is powered) -- I used an alligator clip and a length of wire on my to test

This worked from me after countless hours of testing anything that I could fine, hope it works for you - good luck!


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
13 Replies
6219 Views
Last post March 18, 2011, 03:27:53 AM
by SaminVa.
2 Replies
2090 Views
Last post June 26, 2012, 12:42:24 PM
by sonar2000
9 Replies
3741 Views
Last post March 29, 2013, 11:01:11 PM
by wolfs4evr
3 Replies
1950 Views
Last post April 09, 2013, 04:20:16 AM
by RGecy
2 Replies
1099 Views
Last post June 11, 2013, 08:28:36 AM
by ITGEEK
0 Replies
682 Views
Last post April 14, 2014, 04:07:56 PM
by tokerwashere
2 Replies
778 Views
Last post June 01, 2015, 03:30:11 PM
by Poscast
1 Replies
129 Views
Last post June 12, 2017, 07:25:21 PM
by rnvinc


anything
SimplePortal 2.3.3 © 2008-2010, SimplePortal