Author Topic: iPilot Functions Not Showing Up on 1199 (with Ulterra)  (Read 537 times)

0 Members and 1 Guest are viewing this topic.

Offline snooktarpon

  • Jr. Member
  • **
  • Joined: Apr 2013
  • location: Indiana
  • Posts: 29
  • Unit(s): 1199ci HD SI, 899ci HD SI
  • Accessories: AS-ETH-5PXG
iPilot Functions Not Showing Up on 1199 (with Ulterra)
« on: June 23, 2016, 09:57:22 PM »
I just purchased a 1199ci HD SI (factory refurb) and a Ulterra with iPilot-Link. I've registered the 1199 and the iPilot Link and I verified I have the latest software (7.650 for the 1199 and 2.150 for the iPilot Link). Both came with the latest software installed so I didn't run any updates. I'm also using the Lakemaster Plus map chip (for Great Lakes).

I've have a successfully connection via the ethernet cable when I run an Accessory Test (see attached photo showing the proof). I was reading the older iPilot-Link guide (for the Terrova) since the newer guide is for the Onix. In the guide, its states when you go to Accessories Tab -> iPilot -> iPilot Navigation and turn it on, related i-Pilot Link menus will be added to the
menu system. When I do this, I'm not seeing any of the related i-Pilot Link menus. See my two screenshots (one of the accessories tab and the other is the nav tab).

FYI, I'm testing this in my garage. So I haven't testing this on the water yet (that's for tomorrow). Is the system smart enough to know that I'm not on the water so it doesn't enable the iPilot menus? Or did I fail to configure something?
« Last Edit: June 25, 2016, 09:09:03 AM by snooktarpon »


Offline snooktarpon

  • Jr. Member
  • **
  • Joined: Apr 2013
  • location: Indiana
  • Posts: 29
  • Unit(s): 1199ci HD SI, 899ci HD SI
  • Accessories: AS-ETH-5PXG
Re: iPilot Functions Not Showing Up on 1199
« Reply #1 on: June 24, 2016, 06:15:34 AM »
Just to clairfy, during the setup, the Ulterra is powered on but not deployed. My trailer will interfere with the deployment so I have go out on the water.

So I'm wondering if the iPilot menus will show up once the Ulterra is deployed.

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • location: Western KY
  • Posts: 2961
  • Unit(s): 1197c SI Combo, Onix 8ci SI Combo
  • Software: Dependent on whim
  • Accessories: AS GRHA, AS GPS HS, LowBird LSS 1 & 2
Re: iPilot Functions Not Showing Up on 1199
« Reply #2 on: June 24, 2016, 08:18:22 PM »
I don't think the Ulterra will even power on until it's deployed and locked into position ...

Please post results after your water test ...

Rickie

Offline snooktarpon

  • Jr. Member
  • **
  • Joined: Apr 2013
  • location: Indiana
  • Posts: 29
  • Unit(s): 1199ci HD SI, 899ci HD SI
  • Accessories: AS-ETH-5PXG
Re: iPilot Functions Not Showing Up on 1199
« Reply #3 on: June 24, 2016, 08:47:07 PM »
I'm glad to say that all the iPilot menus came up once I deployed the Ulterra. I wish the owner's manual would have stated that to save me some grief. Now it's time to learn all the iPilot functions.


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
5 Replies
1551 Views
Last post March 29, 2012, 08:13:01 AM
by MichBill
1 Replies
1305 Views
Last post January 07, 2014, 10:11:19 AM
by Humminbird_Greg
4 Replies
1148 Views
Last post March 06, 2015, 03:04:23 PM
by Gimp
5 Replies
2848 Views
Last post April 14, 2015, 09:55:53 AM
by Humminbird_Greg
24 Replies
5916 Views
Last post July 07, 2015, 04:52:53 PM
by yahoo
3 Replies
786 Views
Last post May 03, 2015, 11:15:14 AM
by sfw1960
1 Replies
421 Views
Last post February 14, 2016, 08:19:15 PM
by rnvinc
1 Replies
313 Views
Last post December 02, 2016, 07:34:42 PM
by Bob B


SimplePortal 2.3.3 © 2008-2010, SimplePortal