| Name |
Posted |
Views |
Comments |
Rating |
|
Nauticat 25 Minicat 1976
posted by dybvad417
|
May 15, 2009, 04:33:00 PM |
3614 |
|
|
|
HPIM1052
posted by Roddy
|
September 13, 2012, 09:28:38 PM |
3121 |
|
|
|
THE EQUIPPED FLATS/SAR BOAT 947c, 1158c, 1198c
|
|
HDSI on Lowe Jet Boat
posted by xd35
|
April 15, 2010, 09:03:00 PM |
3031 |
|
|
|
Tranducer Installation on Stepped Deep V Hull
|
April 03, 2009, 06:30:00 PM |
2851 |
|
|
|
Tranducer Installation on Stepped Deep V Hull
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:44:35 PM |
2752 |
|
|
|
2011 nitro z-6
|
|
Humminbird 798c SI transducer on a Ranger 175 under a 5 1/2" CMC Power-Lift jackplate.
posted by John175
|
June 30, 2009, 04:12:24 PM |
2573 |
|
|
|
Humminbird 798c SI transducer on a Ranger 175 under a 5 1/2" CMC Power-Lift jackplate.
|
|
SI on SternMate™ 2
posted by Captn_C
|
March 20, 2010, 12:27:04 PM |
2165 |
|
|
View from port. Hummingbird SI transducer is mounted on a SternMate™ transducer mounting system. The system is installed using a proprietary high speed adhesive without the necessity of damaging screw holes. The boat is our 16DLX Carolina Skiff. Boaters worldwide are now mounting their transom-mounted transducer sounding equipment professionally without compromise to their boat hull. www.sternmate.com |
|
Kayak stern mount 798ci - rear view
posted by kayakangler
|
July 14, 2009, 12:45:39 AM |
2134 |
|
|
|
Fabricated kayak stern mount for my 798ci transducer. Not sure if turbulence from hull will impact the image quality.
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:41:05 PM |
2124 |
|
|
|
2011 Z-6 Transducer 997c si. This was the only place I could see working. If the strap wasnt there I could have moved further over. These z-6 dont have a real good spot for the transducer, I almost canceled the install because of it. I wasnt sure how it would end up working but Im happy to say I took the boat out this morning and it actually worked great.
|
|
1197si on Lowe R 1760 CJ
posted by xd35
|
April 15, 2010, 10:00:01 PM |
2068 |
|
|
|
XNT type Transducer Roostertail Plug
posted by Humminbird_Greg
|
April 03, 2013, 01:18:13 PM |
2036 |
|
|
|
This is the rubber plug that was developed to help stop the water spray from an XNT type transducer when it is mounted low on the transom.
[540188-1 XNT Plug Bagged Hardware]
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:44:01 PM |
1978 |
|
|
|
2011 nitro z-6
|
|
898c SI Speed boat installation pic #5
posted by Erik Concha
|
May 13, 2011, 03:31:41 PM |
1960 |
|
|
|
Transducer Mount on ProCraft Fish and Ski
posted by tenndave
|
February 03, 2011, 05:01:32 PM |
1902 |
1 |
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:43:31 PM |
1861 |
|
|
|
2011 nitro z-6
|
|
Ranger boat si transducer with shield and saver
posted by viers583
|
January 19, 2014, 08:35:42 PM |
1742 |
|
|
|
Drilled 2 holes through step.
|
|
HDSI install on V-Hull
posted by xd35
|
March 15, 2010, 09:04:58 PM |
1740 |
|
|
|
pic 6
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:43:01 PM |
1695 |
|
|
|
2011 nitro z-6
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:42:31 PM |
1678 |
|
|
|
|
|
898c SI Speed boat installation pic #4
posted by Erik Concha
|
May 13, 2011, 03:29:46 PM |
1573 |
|
|
|
DSC06916
posted by J Linville
|
June 10, 2010, 04:45:33 PM |
1572 |
|
|
|
'11 nitro z-6 997c si install
posted by Neverenuff
|
December 10, 2011, 10:41:55 PM |
1560 |
|
|
|
2011 Z-6 Nitro, the ram mount base wouldnt mount up very well due to the difference in height between the console and the actual side of the boat. I ended up taking the arm off the base, drilling one hole and installing a large washer . I used the bolt that came in the arm and put it up through the whole I drilled from the bottom. I installed the rubber next , then the arm finishing off the with the quick connect threaded top that came on the arm. It all worked nicely, it also retained its swivel motion.
|
|
2010 04 27 1746
posted by Deltaden
|
May 02, 2010, 08:12:16 AM |
1557 |
|
|
|
898c Install - Lund 17 Ft Explorer
|
|
2010 04 27 1740
posted by Deltaden
|
May 02, 2010, 08:11:53 AM |
1508 |
|
|
|
898c Install - Lund 17 Ft Explorer
|
|
DSC03742
posted by Beaulieu80
|
August 22, 2014, 08:37:27 AM |
1495 |
|
0.13 (1 vote) |
