Author Topic: 360 issues please help  (Read 2493 times)

0 Members and 1 Guest are viewing this topic.

Offline Bigtiny

  • Newbie
  • *
  • Joined: Jun 2019
  • Location: Alabama
  • Posts: 8
  • Unit(s): Solix 15, Helix 12,360
  • Accessories: 360
360 issues please help
« on: June 20, 2019, 10:06:42 PM »
I have Solix 15 at dash . Helix 12 at trolling motor Ethernet together. I added a 360 and installed it at Ethernet port but it will show good at Solix but at helix it will lose signal after 5 mins. On the phone with huminbird and they tell me that u can’t share images through the Ethernet.they advised me to unplug the helix from Ethernet and run 360 straight to helix. After doing that it runs fine on helix. However now the helix is disconnected from Ethernet I can’t share waypoints. There has to be some settings that I don’t have right.Please advise


Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: 360 issues please help
« Reply #1 on: June 21, 2019, 08:30:32 PM »
Please post the same HB info you posted at Crappie.com  ...

It may help someone here also  ...

Rickie

Offline Bigtiny

  • Newbie
  • *
  • Joined: Jun 2019
  • Location: Alabama
  • Posts: 8
  • Unit(s): Solix 15, Helix 12,360
  • Accessories: 360
Re: 360 issues please help
« Reply #2 on: June 21, 2019, 10:41:15 PM »
i got up this morning since I was off and what do you know it’s working . Best I can figure I have a bad port in my Ethernet box. All I did after a conversation with Wayne p is to move the connections to a different port on Ethernet. Thanks to everyone on this forum for Input and special shot out to Wayne,Rickie. And FYI even according to huminbird site you can share 360 imaging between solix and helix. Below is literature from huminbird site.
When networked together via Ethernet, HELIX and SOLIX models will share:



Waypoints, Tracks & Routes
GPS signal (not mapping)
i-Pilot Link information and control
360 Imaging
Humminbird CHIRP radar
Bluetooth Talon control**
NMEA 2000 network information


*Depending on technology built into each networked fish finder, some sonar images may not be shared if unable to be supported by your unit’s software. Ensure that you are running the latest software by finding updates here: https://www.humminbird.com/support/software-updates
See full compatibility of networking and sonar information here: https://www.humminbird.com/support/f...etSonarSharing
**If both HELIX and SOLIX are on the network and need control of Bluetooth TALONs then at least one SOLIX and one HELIX G2N/G3N must be paired to the Bluetooth TALON at the same time.


Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
2 Replies
14470 Views
Last post May 18, 2011, 03:12:23 PM
by fishinphil
2 Replies
3190 Views
Last post May 06, 2013, 04:59:07 PM
by Humminbird_Greg
5 Replies
6203 Views
Last post May 20, 2013, 09:33:56 PM
by Scrutch
1 Replies
8879 Views
Last post October 10, 2013, 09:04:03 AM
by Humminbird_Greg
2 Replies
8424 Views
Last post June 09, 2014, 03:34:14 PM
by Humminbird_Greg
5 Replies
9032 Views
Last post September 15, 2014, 11:55:03 AM
by Humminbird_Greg
1 Replies
8605 Views
Last post October 02, 2014, 07:24:23 PM
by sfw1960
7 Replies
4048 Views
Last post March 10, 2015, 05:45:48 PM
by rnvinc


SimplePortal 2.3.3 © 2008-2010, SimplePortal