Album

Installatio­n Photos
Featured Album - Owner: RGecy - 111 items
Please post your images or video of your transducer or Unit installtion.  Please put a description of the boat make and model as well as the type transducer and Unit model.
Items view: Normal view Filestack view
Sort by: ID Date Title Views Rating | Sort Order: Ascending Descending
Name Posted Views Comments Rating
ProCraft 205 SI Transducer Install posted by mperdue March 03, 2015, 04:45:14 PM 1380
ProCraft 205 999ci HD Back View posted by mperdue March 03, 2015, 04:43:25 PM 1077
ProCraft 205 999ci HD posted by mperdue March 03, 2015, 04:40:53 PM 969
Helix 5 SI on Dash and Helix 5 DI up front posted by PAPA BEAR February 13, 2015, 02:28:56 PM 1008
Here is where I installed my Helix 5 units. 2002 Ranger 175vs.
DSC03739 posted by Beaulieu80 August 22, 2014, 08:38:13 AM 1310
DSC03742 posted by Beaulieu80 August 22, 2014, 08:37:27 AM 1452 0.13 (1 vote)
DSC03740 posted by Beaulieu80 August 22, 2014, 08:36:37 AM 1342
Ranger boat si transducer with shield and saver posted by viers583 January 19, 2014, 08:35:42 PM 1711
Drilled 2 holes through step.
Ram 111 D mount with HB 898 posted by JDX October 19, 2013, 11:56:33 AM 1346
$75.00 shipped Amazon The best way I found to mount the 898
XNT type Transducer Roostertail Plug posted by Humminbird_Greg April 03, 2013, 01:18:13 PM 2002
This is the rubber plug that was developed to help stop the water spray from an XNT type transducer when it is mounted low on the transom.
[540188-1 XNT Plug Bagged Hardware]
HPIM1052 posted by Roddy September 13, 2012, 09:28:38 PM 3072
THE EQUIPPED FLATS/SAR BOAT 947c, 1158c, 1198c
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:44:35 PM 2716
2011 nitro z-6
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:44:01 PM 1934
2011 nitro z-6
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:43:31 PM 1800
2011 nitro z-6
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:43:01 PM 1649
2011 nitro z-6
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:42:31 PM 1625
2011 nitro z-6
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:41:55 PM 1506
2011 Z-6 Nitro, the ram mount base wouldnt mount up very well due to the difference in height between the console and the actual side of the boat. I ended up taking the arm off the base, drilling one hole and installing a large washer . I used the bolt that came in the arm and put it up through the whole I drilled from the bottom. I installed the rubber next , then the arm finishing off the with the quick connect threaded top that came on the arm. It all worked nicely,  it also retained its swivel motion.
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:41:05 PM 2065
2011 Z-6 Transducer 997c si. This was the only place I could see working. If the strap wasnt there I could have moved further over. These z-6 dont have a real good spot for the transducer, I almost canceled the install because of it. I wasnt sure how it would end up working but Im happy to say I took the boat out this morning and it actually worked great.
'11 nitro z-6 997c si install posted by Neverenuff December 10, 2011, 10:40:34 PM 1362
Heres my 2011 Nitro z-6 install. Not alot of room, took a few inovative ideas.
Packed console!! posted by edwardpic August 16, 2011, 10:43:11 AM 1366
898c SI Speed boat installation pic #5 posted by Erik Concha May 13, 2011, 03:31:41 PM 1924
898c SI Speed boat installation pic #4 posted by Erik Concha May 13, 2011, 03:29:46 PM 1532
898c SI Speed boat installation pic #3 posted by Erik Concha May 13, 2011, 03:28:16 PM 1342
898c SI Speed boat installation pic #2 posted by Erik Concha May 13, 2011, 03:24:48 PM 1272
898c SI Speed boat installation pic #1 posted by Erik Concha May 13, 2011, 03:19:45 PM 1434
Aeva Media 1.4w © 2008-2011 Nao & Dragooon - Wedge: level up your forum!

anything
SimplePortal 2.3.3 © 2008-2010, SimplePortal