ProCraft 205 SI Transducer Install
 Views: 1486
Posted by mperdue
 Mar 03, 2015
|
ProCraft 205 999ci HD Back View
Views: 1176
Posted by mperdue
Mar 03, 2015
|
Views: 1064
Posted by mperdue
Mar 03, 2015
|
Helix 5 SI on Dash and Helix 5 DI up front
Here is where I installed my Helix 5 units. 2002 Ranger 175vs.
Views: 1107
Posted by PAPA BEAR
Feb 13, 2015
|
Views: 1411
Posted by Beaulieu80
Aug 22, 2014
|
Views: 1547
 Rating: 0.13
Posted by Beaulieu80
Aug 22, 2014
|
Views: 1460
Posted by Beaulieu80
Aug 22, 2014
|
Ranger boat si transducer with shield and saver
Drilled 2 holes through step.
Views: 1802
Posted by viers583
Jan 19, 2014
|
Ram 111 D mount with HB 898
$75.00 shipped Amazon The best way I found to mount the 898
Views: 1427
Posted by JDX
Oct 19, 2013
|
XNT type Transducer Roostertail Plug
This is the rubber plug that was developed to help stop the water spray from an XNT type transducer when it is mounted low on the transom.
[540188-1 XNT Plug Bagged Hardware]
Views: 2088
Posted by Humminbird_Greg
Apr 03, 2013
|
HPIM1052
THE EQUIPPED FLATS/SAR BOAT 947c, 1158c, 1198c
Views: 3168
Posted by Roddy
Sep 13, 2012
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 2801
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 2033
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 1910
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
2011 nitro z-6
Views: 1748
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
Views: 1720
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
2011 Z-6 Nitro, the ram mount base wouldnt mount up very well due to the difference in height between the console and the actual side of the boat. I ended up taking the arm off the base, drilling one hole and installing a large washer . I used the bolt that came in the arm and put it up through the…
Views: 1612
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
2011 Z-6 Transducer 997c si. This was the only place I could see working. If the strap wasnt there I could have moved further over. These z-6 dont have a real good spot for the transducer, I almost canceled the install because of it. I wasnt sure how it would end up working but Im happy to say I too…
Views: 2167
Posted by Neverenuff
Dec 10, 2011
|
'11 nitro z-6 997c si install
Heres my 2011 Nitro z-6 install. Not alot of room, took a few inovative ideas.
Views: 1461
Posted by Neverenuff
Dec 10, 2011
|
Views: 1447
Posted by edwardpic
Aug 16, 2011
|
898c SI Speed boat installation pic #5
Views: 2019
Posted by Erik Concha
May 13, 2011
|
898c SI Speed boat installation pic #4
Views: 1616
Posted by Erik Concha
May 13, 2011
|
898c SI Speed boat installation pic #3
Views: 1427
Posted by Erik Concha
May 13, 2011
|
898c SI Speed boat installation pic #2
Views: 1349
Posted by Erik Concha
May 13, 2011
|
898c SI Speed boat installation pic #1
Views: 1515
Posted by Erik Concha
May 13, 2011
|
