Author Topic: 898 si side and down images not working  (Read 3365 times)

0 Members and 1 Guest are viewing this topic.

Offline prmx

  • Newbie
  • *
  • Joined: May 2016
  • Location: monterrey mexico
  • Posts: 4
  • Unit(s): 997c si 798 si helix 5 si
  • Software: newer
898 si side and down images not working
« on: September 13, 2017, 06:00:46 PM »
I have 898 Unit, my side and down image does not work, normal sonar ok the problem occurred after navigating in my bass boat the connector of the transducer was disconnected and reconnected with the unit turned on, sending photos, and I tried another transducer , another cables, software update and I still have theila_rendered same problem, send photos


Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: 898 si side and down images not working
« Reply #1 on: September 13, 2017, 09:58:03 PM »
Have you tried Restore Defaults under the Setup tab  ...??

Rickie

Offline prmx

  • Newbie
  • *
  • Joined: May 2016
  • Location: monterrey mexico
  • Posts: 4
  • Unit(s): 997c si 798 si helix 5 si
  • Software: newer
Re: 898 si side and down images not working
« Reply #2 on: September 14, 2017, 10:50:11 AM »
yes Rickie,

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: 898 si side and down images not working
« Reply #3 on: September 14, 2017, 08:59:42 PM »
As you've already tried another xducer with the same results  ... there is a slim chance both xducers could be bad  ...

About the only other troubleshooting might be to try a different unit on your boat  ...just to verify that the xducer is not faulty  ...

Rickie

Offline prmx

  • Newbie
  • *
  • Joined: May 2016
  • Location: monterrey mexico
  • Posts: 4
  • Unit(s): 997c si 798 si helix 5 si
  • Software: newer
Re: 898 si side and down images not working
« Reply #4 on: September 15, 2017, 11:11:05 AM »
i have on the troll motor a 997 si unit working, with no problems, change the units and the 898 have the same problems in the two sides, and the 997 works in the 2 sites

Offline rnvinc

  • Hero Member
  • *****
  • Joined: Nov 2009
  • Location: Western KY
  • Posts: 4329
  • Unit(s): 1197c SI Combo, SOLIX G2 MSI
  • Software: Dependent on whim
  • Accessories: AS GRHA, MEGA 360, LowBird LSS 1 & 2
Re: 898 si side and down images not working
« Reply #5 on: September 15, 2017, 10:54:09 PM »
You've narrowed it down to the unit  ...

Here's the flat rate charge schedule to decide if you want to send it to HB  ...

https://www.humminbird.com/Category/Support/FAQ/RepairFees/

Rickie



Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo

 

Related Topics

  Subject / Started by Replies Last post
6 Replies
10236 Views
Last post October 10, 2009, 12:04:03 PM
by Humminbird_Greg
2 Replies
2806 Views
Last post April 05, 2010, 06:42:06 PM
by RGecy
5 Replies
11973 Views
Last post July 01, 2011, 02:49:53 PM
by sonar2000
13 Replies
9808 Views
Last post August 21, 2012, 08:26:29 PM
by Ricky
29 Replies
17256 Views
Last post February 06, 2016, 11:53:30 PM
by rnvinc
1 Replies
5016 Views
Last post June 18, 2018, 11:09:25 PM
by rnvinc
5 Replies
6306 Views
Last post December 17, 2020, 09:15:06 PM
by Planokeith
1 Replies
1543 Views
Last post May 03, 2021, 10:56:52 PM
by rnvinc


anything
SimplePortal 2.3.3 © 2008-2010, SimplePortal